UPVC replacement upvc door handles Door Handles

The handles on your doors wear out with time and require to be replaced. When replacing them, it is essential that the new handles conform to the dimensions of the previous handle.

The three measurements to be inspected are the top screw position, lever and key hole dimensions. Use the size guide to aid you.

Inline Lever/Lever

A lever victorian door handle handle is a contemporary handle that can be installed on doors that are new or replacement. This type door handle is offered in a wide range of styles & finishes. This handle is offered by a number of manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door brompton carry Handle

The handles of uPVC/Composite are constructed of tough materials and are ideal for multi-point lock doors that need a heavy-duty design. The handles are inline and run off the same spindle and screw fixings so they are easily installed on existing or new uPVC/Composite doors.

The handle can be placed and angled to suit the needs of all users. The handle has been tested to 200,000 cycles. This helps to ensure that the finish is of high quality and performance is maintained over time. The lever that is sprung can be reduced to accommodate a wider range of locks. This is particularly useful for narrower door frames in which the cylinder is further back. A shortened lever can also be used on doors with a latch that can be activated with the thumb inside.

Lever Pad

The lever pad upvc handle differs from the lever handles that are found on most doors. These handle types can either operate from a single spindle (inline) or independently from each side by using two inline or offset spindles (pad). They are commonly utilized on UPVC doors with double glazing. They come in a range of finishes and variations.

The handles are available in various finishes, including White, Chrome, and Gold. The finish is in line with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, thereby giving the handle a high level of durability and performance for the intended use.

All of the replace upvc door handle lever pad styles for handles come with the spindle and screws that allow them to be put on a new or existing uPVC door. The 211mm backplate fixing centres permit a bigger size of handle which is often a benefit when replacing a window handle a faulty or worn multi-point door lock mechanism. These levers for handles are also sprung, solving the problem of door handles sagging out of the horizontal position when not in use.

It is crucial to ensure that the dimensions of the PZ for both the multipoint lock as well as the uPVC doors when choosing a replacement UPVC spindle and handle. This measurement is also called the 'handle centre' or 'cylinder centres which is a crucial aspect to match the right handles.

Once you have decided on the correct PZ size, you will need to make sure that the lever and push pads are shaped to fit the American with Disabilities Act compliant handles that you need for your door. They are typically round or square, with an internal lever, and an external push pad.

The majority of UPVC Lever Pads we offer are spring-loaded. This means they will return to a horizontal position when they are not in use, rather than hanging and possibly being stuck in the frame. This helps prevent the draughts and cold air from getting into a house. The majority of UPVC lever pad handles come in both left and right handed versions, allowing them to be installed on either side of doors.

Euro Cylinder

Cylinder locks are usually used on uPVC doors, but they can be utilized on other types of doors. They operate by using a key to unlock a cylinder that will reveal pins that can be aligned with those inside the lock body, permitting them to turn a revolving cam, thus opening the door. Euro cylinders can be fitted with up to six pins, with internal and external doors usually having different levels of security.

The choice of cylinder you choose is essential. It is based on the use that your doors and handles will receive. External doors, for instance are required to be fitted with cylinders that are more secure while internal doors can be secured using a standard cylinder. Certain cylinders are equipped with additional features that can increase security, for instance, anti drill or anti bump properties.

To ensure that the euro cylinder is the correct size for your door, it must be measured correctly. The cylinder should be measured from the hole for fixing screws in the middle to each end of the cylinder including the thumb turn if you have one. If you are unable to measure using the lock in a fixed position, you can take it out of it. A cylinder that protrudes beyond the handle and escutcheon could be susceptible to attacks like snapping locks, therefore it is essential to make sure it's not too long.

The majority of modern cylinders have been made with bump and anti-drill features that are built into their design. They are designed to decrease the chance of attack by forcing cylinders to turn in a new direction. This can help to deflect an attack and ensure your door is secure.

Certain cylinders are constructed to resist snapping. This is a typical attack on cylinders. A special tool is used to break the lock's break line and the front of the cylinder is snapped off. This is a much faster and easier way to gain access than a multipoint locking system. It also leaves less evidence of the break-in which could hinder insurance claims.

Spring Cassette

This spring cassette is found within the base plate of your door handle. It provides a sprung solution to bring your multipoint lock handles to their resting position after use. Previously a lot of handles did not have a spring integrated into them and without this they tend to droop or 'drop' once the locking mechanism has been disengaged. Adding this simple component is one of the best methods to correct this issue and is an excellent way to stop your doors made of upvc from getting stuck in the open or closed position, as these aren't always easy to close manually.

These spring cassettes have been specifically made for use with sprung multipoint locks but they won't work with multipoint handles that are not sprung and you will need to have a bespoke hole cut into your backplate in order for them to fit (please check the image for a technical diagram). They are a replacement for broken or missing cassettes within the door handle backplate of many kinds of uPVC doors. They are sold as a single unit. They come with a square cut out that can accommodate an 8mm shaft.

These spring cassettes provide a great value solution to the problem of sagging door handles. These spring cassettes are simple to install and can extend the life of your uPVC door. For more information on our wide range of uPVC spares and accessories you can get in contact with our team. We are always happy to provide expert advice and to assist you.